PPS Dehumidifying dryer PPS dryer can dry to a moisture content below 0.02%, and solves the shortcomings of poor transparency, sprue sticking, bubbles, silver bars, cracks, poor dimensional stability, internal stress, and insufficient product physical strength.
Dehumidification and drying feeding equipment series are composed of: non-heat dehumidification dryer, heat preservation type drying barrel and all stainless steel suction machine. The suction machine can transport the raw materials from the drying barrel to the forming machine, and can also transport the raw materials from the storage barrel to the drying barrel. According to customer needs, a kind of raw material can be delivered to two molding machines, vacuum motors and safety filter dust collectors are installed inside the machine. According to the production needs of different products, we can provide a powder-removing suction machine to separate the powder in the raw material and capture it. This device has a compact structure and is suitable for the production of precision injection products using engineering plastics such as connectors, precision gears, mobile phone communications, digital cameras and product size requirements, so that the moisture content of the raw materials after wet and dry is low and stable, which can meet strict requirements Technical and quality requirements.
Most engineering plastics are hygroscopic. When the plastic is taken out from the moisture-proof sealed packaging bag and exposed to the atmosphere, it will begin to absorb moisture from the atmosphere.
If it is a conventional hot-air barrel dryer, it is Humid external air can dry the plastic, so it cannot prevent the plastic from continuing to absorb moisture.
1. The internal circulation of the dehumidifier: through the operation of the compressor → discharge high-temperature and high-pressure gas through the exhaust port → enter the condenser for cooling → become a low-temperature and high-pressure gas → pass through the capillary tube → become a low-temperature and low-pressure liquid → evaporate and suck through the evaporator Heat → until the compressor becomes a low-temperature and low-pressure gas. So it goes back and forth.
2. The external circulation of the dehumidifier: under normal startup → through the operation of the fan → moist air is sucked in from the air inlet → passes through the evaporator → the evaporator absorbs the moisture in the air on the aluminum sheet → becomes dry air → Pass through the condenser to dissipate heat → blow out from the air outlet.
PPS pellet material dryer application
PPS Dehumidifying dryer With the widespread use of engineering plastics, Dehumidifying dryers have gradually replaced traditional hot air dryers.
This is a device used to dehumidifying plastic resin to achieve drying. For example,
PC,PC/ABS,PC/PBT,PE.HDEPE,LDPE black3%,PE.HDEPE.LDPE black40%,PEEK,PE(1),
Dehumidifier dryerand other plastic resins must be dehumidified and dried during the production process to improve the quality of the finished product.
PPS pellet dryer series are mainly designed for high-efficiency dehumidification of engineering plastics with strong hygroscopicity. Using the honeycomb runner with ceramic fiber as the base material, which represents the highest technological achievements of today, as the core component, the dry air provided can easily reach -40℃ dew point, and ideally it can reach -50℃ or even lower dew point , And the dew point temperature is stable, ensuring the high quality and stability of the molded plastic products. The whole series adopts P.LD. temperature control system as standard equipment; also provides PLC control with LCD touch-sensitive human-machine interface and can monitor the dehumidification effect of the machine Dew point meter is optional, the maximum drying air volume of this product can reach 3000m3/hr. The plastic before molding must be dried to an orientation ratio of less than 0.02%, which is completely bad, sprue adhesion, burrs, bubbles, silver bars, flow marks, cracks, dimensional stability and internal stress. Product defects (for example, insufficient physical properties and strength) are caused by sufficient dehumidification of the plastic before molding. Especially for PET, PBT, PA, PC and other high water absorption plastics, drying equipment with an ultra-low dew point of -40°C is required.
PPS Granule dryer, can be dried to a volume ratio of less than 0.02%, which solves the shortcomings of short circuit, gate adhesion, bubbles, silver bars, cracks, poor dimensional stability, internal stress and insufficient physical strength of the product. There are a lot more.
Mainly used in plastic products, automobiles, optical discs, experiments, communications, optics, etc.; the rotary honeycomb can reach a low dew point of zero bai for dehumidification and drying at -40°C. In the case of enhanced configuration, the dehumidification dew point can be as high as -50°C. It is a choice for high-precision industries.
PPS Granule dryer Precautions
PPS Dehumidifying dryer PPS dryer 1. The humidifier should be cleaned once a week. Do not put the machine in the water during cleaning. The cleaning water temperature should not exceed 50℃; 2. PPS dryer Do not use detergent, kerosene, alcohol, etc. to clean the body and parts; do not disassemble the parts yourself; clean the transducer with a soft brush; wipe the sink with a soft cloth, once every two weeks; wipe the sensor with a soft cloth; the water tank can be cleaned After filling with water, shake it two or three times and pour it out; 3. PPS dryer If the water quality is hard, it is recommended to equip the humidifier with a tap water filter, try to soften the water before filling the humidifier; 4. The humidifier should be rotated on a stable surface with a height of 0.5m-1.5m, away from heat sources, corrosives and furniture, etc., and avoid direct sunlight; use when the relative humidity is less than 80%, adjust the constant humidity button to block RH> 40%-75%. Do not touch the surface of the water with your hands, and do not use it in an empty box. Drain the water in the water tank when moving. Do not put it upside down; the water used must be below 40°C, and other types of chemicals are not allowed; 5. PPS dryer According to your own requirements for humidity, reasonably adjust the spray volume and constant humidity value, do not use it under freezing conditions, and stop immediately when encountering a failure. (1) Ensure that the hot air is clean.
(2) Measures should be taken to prevent coke dust and avoid backflow of hot air.
(3) During the drying process of the material, all parts of the equipment in contact with the material must be cleaned and disinfected.
(4) For viscous materials, measures should be taken to minimize sticking.
(5) In order to improve the solubility, instant solubility, and dry products, they should be continuously discharged from the drying chamber quickly and packaged after cooling.
(6) The exhaust air temperature is allowed to exceed the requirements to ensure product quality and safety.