|
box type Dehumidifing dryer parameter
Box type plastic resin dryer
technical parameter：
| Industry standard model |
Technical parameters Model specifications |
Dry weight per time (kg) |
Equipped with motor power(kw) |
Electric heating power(kw) |
Steam consumption
(kg/h) |
Cooling area
2
(m ) |
Air volume
3
(m /h) |
Temperature difference
(℃) |
With baking tray |
Dimensions
(LxWxH)mm |
Equipped with dryer
(station) |
| RXH-14-B |
CT-I |
120 |
1.1 |
15kw |
20 |
20 |
1400 |
±2 |
48 |
2360×1200×2375 |
2 |
| RXH-27-B |
CT-II |
240 |
1.1 |
30kw |
40 |
40 |
5200 |
±2 |
96 |
2360×2200×2370 |
4 |
| RXH-41-B |
CT-III |
360 |
2.2 |
45kw |
60 |
80 |
9800 |
±2 |
144 |
3300×2200×2560 |
6 |
| RXH-54-B |
CT-IV |
480 |
2.2 |
60kw |
80 |
100 |
9800 |
±2 |
192 |
4250×2200×2560 |
8 |
| RXH-7-C |
CT-C-IA |
60 |
0.45 |
9kw |
10 |
10 |
3450 |
±2 |
24 |
1400×1200×2000 |
1 |
| RXH-14-C |
CT-C-I |
120 |
0.45 |
15kw |
18 |
20 |
3450 |
±2 |
48 |
2300×1200×2000 |
2 |
| RXH-27-C |
CT-C-II |
240 |
0.9 |
30kw |
36 |
40 |
6900 |
±2 |
96 |
2300×2200×2000 |
4 |
| RXH-41-C |
CT-C-III |
360 |
1.35 |
45kw |
54 |
80 |
10350 |
±2 |
144 |
2300×3220×2000 |
6 |
| RXH-54-C |
CT-C-IV |
480 |
1.8 |
60kw |
72 |
100 |
13800 |
±2 |
192 |
4460×2200×2290 |
8 |
| RXH-5-C |
CT-C-O |
30 |
0.45 |
9kw |
5 |
5 |
3450 |
±2 |
8 |
1460×1100×1750 |
1 |
|
box type Dehumidifing dryer Equipment principle
Box type plastic resin dryer
The air circulation system of the hot air circulation oven adopts a fan circulating air supply method, and the air circulation is uniform and efficient. The air source is driven by a circulating air motor (using a non-contact switch) to drive the wind wheel through the heater to send out the hot air, and then to the oven chamber through the air duct, and then suck the used air into the air duct to become the air source for recirculation. Heating use. Ensure the uniformity of indoor temperature. When the temperature value swings due to the opening and closing of the door, the air circulation system quickly restores the operating state until it reaches the temperature value set by the oven.
The hot air circulation oven is divided into five standard models: one-door bicycle oven, two-door two-car oven, two-door four-car oven, three-door six-car oven, four-door eight-car oven; in addition, Qibao drying can be provided according to customer requirements Non-standard customization.
Most of the hot air circulates in the box with high thermal efficiency and energy saving. The oven uses forced ventilation, and an adjustable air distribution board is installed in the oven to dry the materials evenly. The heat source of the oven can be steam, hot water, electricity, far infrared, and a wide range of options. The whole oven has low noise and stable operation. Automatic temperature control, convenient installation and maintenance.
It has a wide range of applications and can dry various materials. It is a universal drying equipment. The arc angle close welding of the inner tank of the oven facilitates the circulation of hot air and is convenient for online cleaning and sterilization. can dry to a moisture content below 0.02%, and solves the shortcomings of poor transparency, sprue sticking, bubbles, silver bars, cracks, poor dimensional stability, internal stress, and insufficient product physical strength.
Dehumidification and drying feeding equipment series are composed of: non-heat dehumidification dryer, heat preservation type drying barrel and all stainless steel suction machine. The suction machine can transport the raw materials from the drying barrel to the forming machine, and can also transport the raw materials from the storage barrel to the drying barrel. According to customer needs, a kind of raw material can be delivered to two molding machines, vacuum motors and safety filter dust collectors are installed inside the machine. According to the production needs of different products, we can provide a powder-removing suction machine to separate the powder in the raw material and capture it. This device has a compact structure and is suitable for the production of precision injection products using engineering plastics such as connectors, precision gears, mobile phone communications, digital cameras and product size requirements, so that the moisture content of the raw materials after wet and dry is low and stable, which can meet strict requirements Technical and quality requirements.
Most engineering plastics are hygroscopic. When the plastic is taken out from the moisture-proof sealed packaging bag and exposed to the atmosphere, it will begin to absorb moisture from the atmosphere.
If it is a conventional hot-air barrel dryer, it is Humid external air can dry the plastic, so it cannot prevent the plastic from continuing to absorb moisture.
1. The internal circulation of the dehumidifier: through the operation of the compressor → discharge high-temperature and high-pressure gas through the exhaust port → enter the condenser for cooling → become a low-temperature and high-pressure gas → pass through the capillary tube → become a low-temperature and low-pressure liquid → evaporate and suck through the evaporator Heat → until the compressor becomes a low-temperature and low-pressure gas. So it goes back and forth.
2. The external circulation of the dehumidifier: under normal startup → through the operation of the fan → moist air is sucked in from the air inlet → passes through the evaporator → the evaporator absorbs the moisture in the air on the aluminum sheet → becomes dry air → Pass through the condenser to dissipate heat → blow out from the air outlet.
|
box type Dehumidifing dryer application
Box type plastic resin dryer
The hot air circulation oven is a wide-applicable tray type intermittent general drying equipment, which is widely used in the heating, curing, drying and dewatering of industrial raw materials or products such as pharmaceuticals, chemicals, food, and light industry. For example: drying of raw materials, herbal medicines, powders, granules, crude drugs, pharmaceutical packaging bottles, pigments, dyes, dehydrated vegetables, food, plastic resins, electrical components, paper, fur, wool, salts, catalysts and other materials.
It is widely applicable to the drying of any plastic raw materials, and can dry materials of different materials and colors at the same time. It is especially suitable for drying materials that require high temperature accuracy, low dosage, and various colors. It is also suitable for preheating or drying in food, pharmaceutical, electronics, electroplating and other industries.
1. Using PI temperature control to accurately control the drying temperature. Integrate temperature and time control into one, 2. It is convenient to set the drying parameters of various materials.
3. High-quality thermal insulation materials and high-sealing design avoid unnecessary energy loss.
5. Adjustable air inlet.
6. Motor overload protection, phase sequence protection.
Working principle of box dryer:
Put the material to be dried into the movable tray. When the power is turned on, the powerful wind wheel starts to force the air entering from the air inlet to blow to the electric heating tube. The air is heated by the electric heating tube and passes through the holed partition. The wall is evenly blown to the material, and the air carrying moisture will be drawn out of the oven by the top moisture exhaust fan. Such repeated cycles can achieve the effect of dehumidification and drying. With the widespread use of engineering plastics, Dehumidifying dryers have gradually replaced traditional hot air dryers.
This is a device used to dehumidifying plastic resin to achieve drying. For example,
POM,ABS,TPE,PAL,ABS,CAB,EVA(2),EVOH,LM(4),LCP,PA11,PA6.46.6,PAI,PAR,PBT,
PC,PC/ABS,PC/PBT,PE.HDEPE,LDPE black3%,PE.HDEPE.LDPE black40%,PEEK,PE(1),
PEN,PES,PET,PETG,PI,PMMA,POM,PP,PPO,PPS,PS,[GPPS.EPS.HIPS],PSU,PIT,PUR,
PVC,SAN,SB,TPE,TPE,TPO,TPU,
Dehumidifier dryerand other plastic resins must be dehumidified and dried during the production process to improve the quality of the finished product.
box type Dehumidifing dryer series are mainly designed for high-efficiency dehumidification of engineering plastics with strong hygroscopicity. Using the honeycomb runner with ceramic fiber as the base material, which represents the highest technological achievements of today, as the core component, the dry air provided can easily reach -40℃ dew point, and ideally it can reach -50℃ or even lower dew point , And the dew point temperature is stable, ensuring the high quality and stability of the molded plastic products. The whole series adopts P.LD. temperature control system as standard equipment; also provides PLC control with LCD touch-sensitive human-machine interface and can monitor the dehumidification effect of the machine Dew point meter is optional, the maximum drying air volume of this product can reach 3000m3/hr. The plastic before molding must be dried to an orientation ratio of less than 0.02%, which is completely bad, sprue adhesion, burrs, bubbles, silver bars, flow marks, cracks, dimensional stability and internal stress. Product defects (for example, insufficient physical properties and strength) are caused by sufficient dehumidification of the plastic before molding. Especially for PET, PBT, PA, PC and other high water absorption plastics, drying equipment with an ultra-low dew point of -40°C is required.
box type Dehumidifing dryer can be dried to a volume ratio of less than 0.02%, which solves the shortcomings of short circuit, gate adhesion, bubbles, silver bars, cracks, poor dimensional stability, internal stress and insufficient physical strength of the product. There are a lot more.
Mainly used in plastic products, automobiles, optical discs, experiments, communications, optics, etc.; the rotary honeycomb can reach a low dew point of zero bai for dehumidification and drying at -40°C. In the case of enhanced configuration, the dehumidification dew point can be as high as -50°C. It is a choice for high-precision industries.
box type Dehumidifing dryer Precautions
The box dryer should be cleaned and maintained regularly, especially the granulating oven and dryer should not be checked every day. Some pharmaceutical companies need to work in three shifts. It is recommended that each shift be controlled within 6 hours.
It is necessary to strengthen the management of safe operation of employees, safeguard the vital interests of employees, and ensure the smooth progress of production. It is strictly forbidden to work after drinking, lack of sleep, and work in a trance, and other influences on work.
|
|
|
+8613669807274
